Husqvarna 232R Manual do Utilizador

Operator's Manual (CARB, EPA)101 89 27-95Read through the Operator's Manual carefully andunderstand the content before using the machine.225

10 – EnglishGeneral working instructionsSAFETY INSTRUCTIONS4.Take great care whencutting a tree that is subjectto tension. A tree that isunder tension

English – 11SAFETY INSTRUCTIONSAdjusting the harness and clearing sawDesignations• Forestry clearing is ageneral term for cuttingsmall trees where eac

12 – EnglishSAFETY INSTRUCTIONSClearing‘s ABCA. Always use the correct equipment.B. Always have well adjusted equipment.C. Follow the safety instructi

English – 13SAFETY INSTRUCTIONS• Large stems must be cutfrom two sides.Determine in whichdirection the stemshould fall. First applythe saw to the fell

14 – EnglishSAFETY INSTRUCTIONSGrass trimmingusing the trimmerhead• Hold the trimmer headjust above the ground atan angle. It is the end ofthe cord th

English – 15WHAT IS WHAT?What is what on the brush cutter?1. Blade2. Grease filler cap3. Angle gear4. Blade guard5. Shaft6. Handlebars7. Throttle8. St

16 – EnglishAssembling the handlebars(225R/RD/ 232R/RD)ASSEMBLYAssembling the handlebars (235R)• Remove the screw at therear of the throttle handle.•

English – 17ASSEMBLYAssembling the J-handlebars(225RJ)• The handlebars can easilybe turned to fit along theshaft for easytransportation and storage.•

18 – EnglishASSEMBLYIMPORTANT INFORMATIONThe machine must be equipped with the correcthandlebars, blade guard and harness if either aclearing blade or

English – 19ASSEMBLYAssembling the spray guard andtrimmer head Superauto II(225R/RD/ 232R/RD)KJIGFIMLAKBC• Fit the guard (A) intendedfor use with the

2 – EnglishSymbolsSYMBOL EXPLANATIONWARNING! Clearing saws, brushcutters and trimmers can bedangerous!Careless or incorrect use can result inserious o

20 – EnglishAdjusting the harness and clearingsaw!WARNING!When working with the clearing saw itshould always be hooked in the harness.If this is not d

English – 21FUEL HANDLINGFuel mixture• Clean around the fuelcap. Contamination inthe tank can disruptoperations.• Ensure that the fuel iswell mixed by

22 – EnglishSTART AND STOPControl before startingCold engineIGNITION: Set the stopswitch to the start position.CHOKE: Set the chokecontrol in the cho

English – 23CarburettorYour Husqvarna product has been designed andmanufactured to specifications that reduce harmfulemissions.After your unit has bee

24 – EnglishFinal setting of the idling speed TAdjust the idling speed withthe screw T, If it is necessaryto readjust. First turn theidle speed adjust

English – 25MAINTENANCECooling systemTo maintain as low opera-ting temperature as possiblethe engine is equipped witha cooling system.The cooling syst

26 – EnglishMAINTENANCESpark plugThe condition of the sparkplug is affected by:• An incorrect carburettorsetting.• An incorrect fuelmixture (too much

English – 27MAINTENANCENOTE: Use only HUSQVARNA replacement parts. Use ofother brands of replacement parts can cause damage to yourunit or injury to t

28 – EnglishTECHNICAL DATATechnical dataEngineCylinder capacity, cu. in/cm3Cylinder bore, inch/mmStroke length, inch/mmIdling speed, rpmRecommended ma

English – 29TECHNICAL DATAApproved accessories 225R/RD/RJCentre hole in blades Ø 20 mmThreaded blade axle M10Grass bladeSaw blade (Not 225RJ)Plastic k

English – 3Before using a new machine• Read the Operator‘s Manual carefully.• Check the assembly and adjustment of the cuttingequipment. See page 18-1

30 – EnglishYOUR WARRANTY RIGHTS ANDOBLIGATIONSThe EPA (U.S. Environmental Protection Agency), Carb(California Air Resources Board) and Husqvarna Fore

4 – EnglishThe machine‘s safety equipmentThis section describes the machine‘s safety equipment, itsfunction and how checks and maintenance are carried

English – 56. MufflerThe muffler is designed togive the lowest possible noiselevel and to direct theengine‘s exhaust fumes awayfrom the operator. Muff

6 – EnglishSAFETY INSTRUCTIONS1. Throttle triggerlock• Check that the throttle islocked in the “idlingposition“ when thethrottle trigger lock is inits

English – 77. Quick-release• Check that the harnessstraps are correctlypositioned. When theharness and machine areadjusted, check the harness‘safety r

8 – EnglishSAFETY INSTRUCTIONSFiling the grassblade• See the cuttingequipment’s packaging forcorrect filing instructions.• The blades are sharpenedusi

English – 9SAFETY INSTRUCTIONSGeneral safety instructionsIMPORTANT INFORMATION• The machine is only designed for trimming grass,brush cutting and/or f