Husqvarna 385XP Manual do Utilizador

EEEEnnnngggglllliiiisssshhhh 385XP Operator ′ s manual Please read the operator’s manual carefully and make sure youunderstand the instructions befo

10 – English SAFETY INSTRUCTIONS Combining these links in different ways gives different degrees of kickback reduction. In terms of kickback reducti

English – 11SAFETY INSTRUCTIONSWhen you sharpen a cutting tooth there are five important factors to remember.1 Filing angle2 Cutting angle3 File positi

12 – EnglishSAFETY INSTRUCTIONS• We recommend that you use our raker gauge to achieve the correct clearance and bevel on the raker lip.Setting the rak

English – 13SAFETY INSTRUCTIONSFilling with chain oil• All our chain saws have an automatic chain lubrication system. On some models the oil flow is al

14 – EnglishSAFETY INSTRUCTIONSChecking wear on cutting equipmentCheck the chain daily for:• Visible cracks in rivets and links.• Whether the chain is

English – 15SAFETY INSTRUCTIONSKickback always occurs in the cutting plane of the bar. Normally the chain saw and bar are thrown backwards and upwards

16 – EnglishSAFETY INSTRUCTIONS8 Follow the instructions on sharpening and maintaining your bar and chain. When you replace the bar and chain use only

English – 17SAFETY INSTRUCTIONS• Observe your surroundings and make sure that there is no risk of people or animals coming into contact with the cutti

18 – EnglishSAFETY INSTRUCTIONS• Take great care when removing small branches and avoid cutting bushes (i.e. cutting many small branches at the same t

English – 19SAFETY INSTRUCTIONS4 Is there a risk of kickback?5 Do the conditions and surrounding terrain affect how safely you can stand and move abou

2 – English KEY TO SYMBOLS Key to symbols WARNING! Chain saws can be dangerous! Careless or incorrect use can result in serious or fatal injury to t

20 – EnglishSAFETY INSTRUCTIONSTree felling techniqueSafe distanceThe safe distance between a tree that is to be felled and anyone else working nearby

English – 21SAFETY INSTRUCTIONSThe directional cuts should run 1/4 of the diameter through the trunk and the angle between the top cut and bottom cut

22 – EnglishSAFETY INSTRUCTIONSLimbingMake sure that you can stand and move about safely. Work on the left side of the trunk. Work as close as possibl

English – 23WHAT IS WHAT?What is what on the chain saw?Husqvarna XXXXHusqvarna ABHuskvarna, SWEDENXXXXXXXXXXX1 Cylinder cover2 Front handle3 Front han

24 – EnglishASSEMBLYFitting the bar and chainCheck that the chain brake is in disengaged position by moving the front hand guard towards the front han

English – 25FUEL HANDLINGFuelCAUTION! The machine is equipped with a two-stroke engine and must always been run using a mixture of petrol and two-stro

26 – EnglishFUEL HANDLINGFuellingClean the area around the fuel cap. Clean the fuel and chain oil tanks regularly. The fuel filter must be replaced at

English – 27STARTING AND STOPPINGStarting and stoppingCold engineStarting: The chain brake must be engaged when the chain saw is started. Activate the

28 – EnglishSTARTING AND STOPPINGReactivate the chain brake by pushing the front hand guard back towards the front handle. The chain saw is now ready

English – 29MAINTENANCECarburettor adjustmentThe carburettor can be designed in different ways, depending on existing environmental and emissions legi

English – 3 CONTENTS Contents Before using a new chain saw • Please read the operator’s manual carefully.• Check that the cutting equipment is corre

30 – EnglishMAINTENANCE• Now start the machine according to the starting instructions and let it warm up for 10 minutes. CAUTION! If the chain rotate

English – 31MAINTENANCEIf you are unable to check the fast idle speed using a tachometer the H-jet should not be set for a leaner mixture than given i

32 – EnglishMAINTENANCEStarterChanging a broken or worn starter cord• Loosen the screws that hold the starter against the crankcase and remove the sta

English – 33MAINTENANCEAir filterThe air filter must be regularly cleaned to remove dust and dirt in order to avoid:• Carburettor malfunctions• Starting

34 – EnglishMAINTENANCENeedle bearing lubricationThe clutch drum is fitted with one of the following drive sprockets:• A Spur sprocket (the chain spr

English – 35MAINTENANCEElectrical carburettor heating(385XPG)If this chain saw has the model code XPG/G then it is equipped with an electrically heate

36 – EnglishMAINTENANCEBelow you will find some general maintenance instructions.Daily maintenance1 Check that the components of the throttle control w

English – 37TECHNICAL DATATechnical dataNote 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/

38 – EnglishTECHNICAL DATA´®z+H<@¶6E¨´®z+H<@¶6E¨Bar and chain combinationsThe following combinations are CE approved.BarChainLength, inchesPitch

EC-declaration of conformity(Applies to Europe only)Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel +46-36-146500, declares under sole responsibility t

4 – English SAFETY INSTRUCTIONS Personal protective equipment • Protective helmet• Hearing protection• Protective goggles or a visor• Gloves with sa

´®z+H<@¶6E¨2004-09-10´®z+H<@¶6E¨1140283-26

English – 5 SAFETY INSTRUCTIONS Chain brake and front hand guard Your chain saw is equipped with a chain brake that is designed to stop the chain im

6 – English SAFETY INSTRUCTIONS • During felling your left hand grasps the front handle in such a way that it cannot activate the chain brake. In th

English – 7 SAFETY INSTRUCTIONS Muffler The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.In ar

8 – English SAFETY INSTRUCTIONS Grasp the chain saw firmly, wrapping your fingers and thumbs around the handles.Apply full throttle and activate the c

English – 9 SAFETY INSTRUCTIONS If the muffler on your machine is fitted with a spark arrestor mesh this must be cleaned regularly. A blocked mesh wil